LG Washing Machine Shakes Violently During Spin Cycle (Easy Fixes)

When that washing machine starts to sound like a helicopter taking off, it’s enough to make anyone jump. You’ve got a load of laundry you need done, but your LG washer has decided to put on a show, shaking and vibrating like it’s going to break apart. It’s a common problem, but one that needs your attention before real damage happens. I’m here to walk you through exactly what’s going on and how to fix it.

Your LG washing machine shakes violently during the spin cycle because of an unbalanced load, worn-out shock absorbers, or a loose drum bearing. You must check the load distribution first, as this is the easiest fix. If the shaking persists, you’ll need to inspect and possibly replace internal components. Ignoring this loud banging sound can cause serious damage.

Why Your Washer Starts to Buck and Jump

Unbalanced Loads

The most common culprit is how you load your clothes. When heavy items, like towels or jeans, bunch up on one side, the drum spins unevenly. Your machine’s sensors try to compensate, but they can only do so much against a significant imbalance. You might not realize how much one side is heavier than the other until it’s too late.

This uneven weight distribution is a major cause of violent shaking during spin. It puts a lot of stress on the machine’s suspension system, and over time, this can lead to more serious issues if you don’t correct it. Your washer is designed for balance, and when you don’t give it that, it fights back.

So, next time you load, take a moment to spread the items around evenly. If you’re washing a single heavy item, try adding a few lighter ones to balance it out. Your appliance will thank you with a smooth, quiet spin.

Uneven Floor

A washing machine needs a stable, level surface to operate correctly. If your floor isn’t perfectly flat, or if the machine itself has uneven legs, it can amplify any minor imbalances. You might think the machine is the problem, but sometimes the ground beneath it is the real issue.

Even a slight tilt can cause the machine to move and vibrate excessively during the spin cycle. This movement can make the shaking seem much worse than it actually is, and it can also put undue stress on the machine’s frame. You want your washer to be planted firmly.

You can buy a small level to check if your machine is sitting flat. Most machines have adjustable feet that you can twist up or down to correct any tilt. Taking a few minutes to level your washer ensures it operates as smoothly as the manufacturer intended.

Drum Weight

Over time, the drum itself can become unbalanced internally, even without a load. This can happen if small items like socks or coins get trapped between the inner and outer drums. It’s not common, but it is a possibility that could lead to severe vibrations.

This trapped debris, or sometimes even a build-up of lint and soap scum, can create a consistent off-balance condition. Your machine might start shaking even with a perfectly balanced load of clothes. It’s like having a tiny, stubborn weight attached to one side constantly.

When you do a load of laundry, make sure your pockets are empty and smaller items are secured. You might need to run a cleaning cycle with a washing machine cleaner to tackle any internal build-up. This preventative maintenance can save you headaches later.

Suspension System

Every washing machine has a suspension system, usually with shock absorbers or springs, designed to absorb the vibrations from the spinning drum. If these components wear out or break, there’s nothing to dampen the movement. This leads directly to the machine shaking excessively.

Think of it like the shocks on your car. If they’re worn out, every bump in the road is felt much more intensely. The same thing happens inside your washer when the suspension parts fail. You’ll feel and hear the difference immediately.

This is a repair that often requires a technician, as accessing these parts can be tricky. But knowing that your suspension might be shot helps you understand the root cause of the violent shaking you’re experiencing. You can try gently pushing down on the drum; if it feels loose or bounces excessively, your suspension is likely the problem.

Drive Belt Issues

A worn or damaged drive belt can cause the drum to spin erratically, or even intermittently, during the spin cycle. This inconsistent rotation can lead to sudden, jerky movements, mimicking an unbalanced load but with a different underlying cause. You might notice a slapping or thumping noise associated with the shaking.

The belt connects the motor to the drum, and if it’s slipping or frayed, the power transfer isn’t smooth. This causes the drum to lurch instead of spin steadily. It’s a crucial part of your washer’s mechanics, and its failure impacts the entire spin cycle.

Checking the drive belt usually involves tipping the machine back or removing a back panel. You’ll need to see if the belt is cracked, frayed, or loose. If it looks worn, replacing it is often a manageable DIY job for many people.

Bearing Failure

The drum bearings allow the drum to spin smoothly on its axis. If these bearings wear out or get damaged, you’ll often hear a grinding or rumbling noise that gets louder as the spin speed increases. This damaged bearing makes the drum wobble, leading to violent shaking.

This is one of the more serious issues you can face. When bearings fail, they can seize up, making the drum impossible to turn or causing catastrophic damage. The wobbly drum is a clear sign that your bearings are on their way out, or already gone.

Repairing or replacing drum bearings is usually a job best left to a professional. It involves disassembling a large portion of the washing machine, and it requires specific tools and knowledge to do it correctly. You don’t want to make things worse by attempting this if you’re not experienced.

This section has covered the common reasons your LG washer shakes. Understanding these background issues is key.

Now, let’s focus on getting that shaking stopped.

How to Fix a Shaking LG Washing Machine During Spin

Dealing with a washing machine that shakes violently during the spin cycle is a common annoyance, but thankfully, many causes are easy for you to address. You don’t always need a repair person. This section focuses on the practical steps you can take right now to stabilize your LG washer.

Balance Your Loads

This is the first and easiest thing you can do. When you load your washing machine, make sure the clothes are distributed evenly around the drum. Avoid putting all the heavy items, like bedding or towels, on one side. You want to create a symmetrical weight distribution for the spin cycle.

If you’re washing a single large item, like a comforter, it’s best to add a few smaller items to balance it out. Sometimes, clothes can clump together during the wash phase, creating an imbalance that leads to that violent shaking and banging. You’ll hear the difference when it’s properly balanced.

Check your machine after it starts to spin. If you see one side is much heavier, pause the cycle and rearrange the clothes. This simple adjustment can prevent the overloaded drum from causing excessive movement and stress on your appliance.

Check Leveling Feet

Washing machines need to sit perfectly level to operate without vibrating excessively. If your machine is rocking back and forth, the leveling feet might be out of adjustment or damaged. You should always start by checking this basic stability. Your appliance needs a solid foundation.

Most LG washing machines have adjustable feet at the base. You can twist these feet up or down to raise or lower each corner until the machine is perfectly stable and doesn’t rock. A small bubble level can help you verify that your machine is sitting perfectly flat. You want to eliminate any wobble.

If the feet are damaged or won’t adjust, you might need to replace them. However, most of the time, a simple adjustment is all that’s needed to stop the machine from dancing across the floor. This is a quick fix that makes a big difference.

Inspect Shock Absorbers

The shock absorbers are the unsung heroes that keep your washing machine from vibrating itself apart. They absorb the energy from the spinning drum. If they are worn out, leaking, or broken, the shaking will be significantly amplified. You might notice the drum bounces excessively when you push down on it.

Accessing the shock absorbers usually involves tipping the machine back or removing a rear panel. You’ll want to look for signs of damage, like cracks, or oil leaks, which indicate they are no longer functioning properly. Your machine relies on these to stay grounded.

Replacing these can be a moderately difficult DIY task. You’ll need to identify the correct part number for your specific LG model and ensure you have the right tools. If you’re not comfortable with this type of repair, it’s best to call a professional to handle it.

Examine Drive Belt

The drive belt connects the motor to the drum, allowing it to spin. If this belt is worn, stretched, or has a chunk missing, it can cause the drum to spin erratically, leading to a shaking machine. You might also hear a whirring or slapping sound when the washer is in its spin cycle.

To check the drive belt, you will likely need to remove the back panel of the washing machine. Look for any signs of wear, such as cracks, fraying, or excessive looseness. A belt that has lost its tension will not be able to spin the drum smoothly. Your washer needs a good belt to work.

If you find that the drive belt is damaged, you’ll need to replace it. Make sure you order the exact replacement part for your LG model. Replacing the belt itself is often straightforward, but working inside the machine requires caution.

Test Drum Bearings

Worn-out drum bearings are a common cause of loud rumbling or grinding noises during the spin cycle, and this often leads to significant shaking. If you can spin the drum by hand and hear a rough sound, or if it feels loose and wobbly, the bearings are likely the problem. This is a more serious repair.

You can often diagnose this by trying to move the inner drum up and down. If there’s a lot of play or if you hear scraping, it’s a strong indicator that the bearings are failing. This is a part that takes a lot of abuse over the years, and they do wear out.

Repairing drum bearings is typically a complex job that involves disassembling much of the washing machine. For most people, it is more practical to call a qualified appliance technician. You don’t want to risk further damage by attempting a repair beyond your skill level.

Check Motor Mounts

The motor is bolted to the frame of the washing machine, and these mounts can loosen or break over time. If the motor is not securely attached, its vibrations can be transferred directly to the machine’s chassis, causing excessive shaking and noise. You should inspect these mounts carefully.

Loose motor mounts can allow the motor to shift during operation, leading to an off-balance spin and intense vibrations. You might be able to tighten them with a wrench if they are simply loose. However, if the rubber mounts are cracked or broken, they will need to be replaced.

This repair involves getting under the machine or accessing the motor from the back. Ensure you disconnect the power before you start inspecting. Properly securing the motor is crucial for a stable spin cycle, so you must address this if it’s the cause.

This section gave you the main fixes. Now, let’s look at other things.

Can You Wash a Single Heavy Item

Washing a single heavy item, like a large duvet or a dense bath mat, can cause significant imbalance in your washing machine. When the machine spins, this heavy item will naturally want to collect on one side of the drum. This creates a severe off-balance load that your washer will struggle to manage.

Even if the machine tries to correct it, the weight distribution is so uneven that the damp fabric will likely stay bunched up. You’ll hear the machine banging and shaking quite violently as it attempts to spin. This situation puts a lot of stress on the drum, suspension, and the entire frame of your appliance.

The best approach is always to balance heavy items with lighter ones. If you only have one large item, consider taking it to a laundromat with larger capacity machines. Your LG washer isn’t designed for single, unbalanced heavy loads, and you want to avoid causing damage.

Wash with Lighter Items

To counteract the imbalance caused by a single heavy item, always add a few lighter towels or sheets to the load. These items help to distribute the weight more evenly around the drum during the spin cycle. You’re essentially creating a more stable environment for the heavy item.

This simple trick ensures that as the heavy item tries to bunch up, the lighter items can help pull it around and keep the load more centered. You’ll notice a huge difference in how the machine performs. Your washer won’t sound like it’s about to take flight.

It’s a small step that significantly reduces the strain on your washing machine’s components. You’ll get a cleaner wash, and your machine will operate much more smoothly and quietly, preventing potential damage.

Use a Smaller Load

If you only have a few heavy items and no lighter ones to balance them, consider doing multiple smaller loads instead of one big, unbalanced one. This might take a bit more time, but it’s far better for your machine’s longevity. Your appliance will thank you for it.

Breaking down the load ensures that each cycle is more manageable for your LG washer. Even if you have to run the machine twice, it’s a better option than risking the wear and tear caused by a severely unbalanced load in a single cycle. You want to keep your machine running smoothly.

By being mindful of how you load your machine, you can prevent common issues like excessive shaking and banging. It’s all about understanding how your washer operates and giving it the best chance to perform well.

Consider Laundromat Use

For extremely bulky items like king-size comforters or large sleeping bags, your home washing machine might simply not be up to the task. These items absorb a lot of water, become incredibly heavy, and are almost impossible to balance in a standard-sized drum. You might need to seek professional help.

Many laundromats have commercial-grade machines that are designed to handle these types of loads with ease. They have more powerful motors and sturdier suspension systems. Taking your bulky items there ensures they are cleaned properly without risking damage to your home appliance.

It’s an extra trip, but it’s a good investment in protecting your washing machine. You’ll avoid the stress and potential damage that comes from trying to force oversized items through a cycle they’re not meant for.

How Do You Troubleshoot a Washer That Leaks

When your LG washing machine shakes violently during the spin cycle, it’s often accompanied by other issues, like leaks. A leak can happen for many reasons, but it always means you have a problem that needs fixing. You don’t want water pooling around your appliance.

Leaks can occur from hoses, seals, or even a crack in the machine’s tub. The first step is always to identify the source of the water. Is it coming from the back, the front, or underneath the machine? Your ability to pinpoint the leak will guide your repair efforts.

Sometimes, simple things like a loose drain hose or a cracked fill hose are the culprits. Other times, it’s a more complex issue with internal seals. You need to address any leak promptly, as water damage can be extensive and costly to repair.

Worn Door Seal

The rubber seal around the door of your front-load LG washing machine is critical for preventing leaks. Over time, this seal can degrade, crack, or develop small tears, especially if you’ve been washing items with zippers or sharp edges that can snag it. You’ll notice water pooling on the floor in front of the machine.

If you see water escaping from the bottom of the door after the wash or spin cycle, inspect the seal closely. Run your finger around it to feel for any rough spots, nicks, or tears. It should be smooth and intact all the way around. This seal prevents the water from escaping during aggressive cycles.

Replacing the door seal is usually a manageable DIY repair, though it can be a bit fiddly. You’ll need to order the correct part for your model and follow a good guide or video tutorial. Properly seating the new seal is key to a watertight fit.

Loose Hose Connections

Check all the hoses connected to your washing machine – the inlet hoses for water and the drain hose. Ensure they are securely fastened to both the machine and the water supply or drain pipe. A loose connection, especially on the drain hose during the spin cycle, can cause water to splash out.

Over time, the clamps holding these hoses can loosen, or the rubber hoses themselves can become brittle and crack. Vibrations from the machine can exacerbate these issues, leading to a drip or spray of water when you least expect it. You should always check these connections.

A simple tightening of a clamp might solve your problem, but if a hose is visibly cracked or deteriorated, it needs to be replaced entirely. Don’t risk a major leak; inspect your hoses regularly.

Tub Seal Failure

The main tub seal, located where the drum shaft enters the outer tub, is another common source of leaks. If this seal fails, water can leak from the center of the tub, often appearing underneath the machine. This is a more serious repair than a hose or door seal.

This seal prevents water from entering the area where the motor and bearings are housed. When it fails, water inevitably finds its way out. You might also notice that the shaking is accompanied by a distinct grinding noise if the bearings are also compromised.

Repairing the tub seal usually requires significant disassembly of the washing machine. It’s often a job that requires specialized tools and a good understanding of the machine’s mechanics. You will likely need to call a professional for this repair.

Clogged Drain Pump

If your washing machine isn’t draining properly, the water can back up and cause leaks, especially during the spin cycle when water should be expelled. A clogged drain pump or filter is a frequent cause of this. You might notice water left in the drum after the cycle finishes.

Check the drain pump filter, usually located at the bottom front of the machine behind a small access panel. Carefully remove it to clean out any debris like lint, coins, or small clothing items. Make sure you have towels ready, as some water will likely spill out.

If the filter is clear and the pump still isn’t working efficiently, the pump itself might be failing. You can sometimes hear the pump struggling or making unusual noises when it’s clogged or failing. Keeping this filter clean is essential maintenance.

Cracked Outer Tub

In rare cases, the outer plastic tub of the washing machine can develop a crack, leading to leaks. This is often caused by a foreign object getting between the inner and outer tubs, or by the machine being subjected to extreme stress, such as from very violent shaking. You’ll see water leaking from the bottom of the machine.

A cracked outer tub is a serious problem, as it’s a major component that is difficult and expensive to replace. It might even be more cost-effective to replace the entire washing machine. You’ll want to carefully inspect the entire tub for any signs of damage.

If you discover a crack, you need to stop using the machine immediately to prevent further damage or electrical hazards. This is usually a sign that your washer has reached the end of its useful life. You need to consider a replacement.

What Tools Are Needed

Before you start troubleshooting or fixing your LG washing machine that shakes violently during spin cycle, you’ll need a few basic tools. Having the right equipment makes the job much easier and safer. Don’t try to force things with the wrong tools; you could cause more damage.

Your toolkit doesn’t need to be extensive for most common fixes. A few common hand tools will likely get you through many of the necessary adjustments and minor repairs. Having these on hand means you can tackle issues promptly. You want to be prepared.

Having a small variety of screwdrivers, wrenches, and pliers is usually sufficient for most basic tasks. If you plan on more involved repairs, you might need specialized tools, but start with the essentials.

Screwdrivers Set

You’ll need a set of screwdrivers, including Phillips head and flathead varieties. Many washing machine panels and components are held in place with screws, and you’ll need the right size and type to remove them without stripping the heads. This is fundamental.

Make sure your set includes a range of sizes. Sometimes a screw is recessed, and you might need a longer shaft, or it might be a very small screw that requires a precision driver. You don’t want to find yourself unable to undo a screw because you don’t have the right driver.

Having a magnetic tip on your screwdrivers can also be a lifesaver, preventing screws from falling into hard-to-reach places inside the machine. You’ll appreciate this feature when working in tight spots.

Adjustable Wrench

An adjustable wrench, often called a Crescent wrench, is incredibly useful. It allows you to fit a variety of bolt and nut sizes. This is particularly handy for adjusting the leveling feet or tightening hose clamps. You can cover many sizes with just one tool.

You’ll find yourself using an adjustable wrench for various tasks around the house, not just for washing machine repairs. Make sure you get a decent quality one that adjusts smoothly and holds its position firmly when you’re applying pressure. You want it to be reliable.

When using it, ensure the jaws are snug against the nut or bolt head to prevent slipping, which can round off the edges. This tool is a staple for anyone who does their own home repairs.

Pliers

A good pair of pliers is essential. Needle-nose pliers are great for reaching into tight spaces to grab small parts or wires. Standard slip-joint pliers can be used for gripping and turning, especially for hose clamps or stubborn nuts. You might also find channel lock pliers useful for larger jobs.

Having a few different types of pliers ensures you have the right tool for the job. Sometimes a simple grip is all you need to loosen a stubborn connection, or to hold a part in place while you tighten something else. They are incredibly versatile.

Look for pliers with comfortable grips, as you might be using them for a while. Quality pliers are a worthwhile investment for any home toolkit, and they will serve you well for many appliance repairs.

Socket Set

While an adjustable wrench covers many bases, a socket set can be more efficient for specific bolts and nuts. Having a set with common socket sizes and a ratchet handle makes it easier to remove bolts that might be in tight or awkward positions. It speeds up the job.

You’ll find that some parts of the washing machine might use hex bolts that are best turned with a socket. A socket set, especially one with a few extension bars, can give you the leverage and reach you need. This makes the job less frustrating for you.

When choosing a socket set, look for one made from durable chrome vanadium steel. This ensures they won’t rust or deform easily. A good socket set is a cornerstone of any serious DIY repair kit.

Work Gloves and Safety Glasses

Always protect yourself. Work gloves will prevent cuts, scrapes, and grease stains on your hands. Safety glasses are crucial to protect your eyes from falling debris, dust, or accidental splashes of water or cleaning agents. You don’t want an accident to sideline your repair efforts.

Wearing gloves also provides a better grip on greasy or slippery parts. Safety glasses are non-negotiable whenever you are working on any appliance, especially when dealing with internal components. You should always prioritize your safety.

These items might seem basic, but they are essential for any repair work. Always wear them, and you’ll avoid unnecessary injuries. It’s a small step that makes a big difference in your safety and comfort.

What Causes Drum Wobble

A wobbly drum is the primary reason your LG washing machine shakes violently during spin. It’s not just about the clothes inside; it’s about the structural integrity of the drum and its support system. You need to understand what causes this wobble to fix it.

The drum spins at very high speeds, and any imbalance is magnified. When you can see or feel the drum moving excessively, it means something is loose, worn out, or broken. This wobble puts tremendous strain on everything connected to the drum.

This is why addressing drum wobble is so important; it’s the root cause of most violent shaking and banging. Your machine is trying to tell you it’s fundamentally unstable.

Worn Suspension Springs

Many washing machines use heavy-duty springs to suspend the tub assembly. These springs absorb the forces generated during the spin cycle. If these springs become stretched, weakened, or break, the tub will sag or bounce excessively, causing severe drum wobble.

You can often see these springs if you look up from underneath the machine, or by removing the back panel. If a spring looks visibly saggy compared to others, or if it’s detached, that’s your problem. Your washer needs these to stay steady.

Replacing suspension springs is often a manageable DIY task. You’ll need to carefully unhook the old springs and attach the new ones, ensuring they are properly seated. This is a common repair that can bring your machine back to life.

Damaged Shock Absorbers

As mentioned earlier, shock absorbers work in conjunction with springs to dampen vibrations. If they are worn out, leaking, or broken, they can’t effectively control the tub’s movement. This leads to a loose, uncontrolled drum wobble.

You can test the shock absorbers by pushing down firmly on the outer tub. If it bounces back up multiple times or feels very loose, the shocks are likely bad. They should provide resistance and stop the bouncing quickly. Your machine relies on them for stability.

Replacing shock absorbers usually requires removing the outer tub or tipping the machine. It’s a repair that requires some mechanical aptitude. If you’re not comfortable with this, it’s best to call a technician.

Loose Drum Bearings

When drum bearings fail, they can cause the drum to become loose on its shaft. This looseness translates directly into a wobble. You’ll typically hear a loud grinding or rumbling noise that gets worse as the spin speed increases. This is a serious indicator.

A damaged bearing means the drum isn’t spinning true. It’s like trying to spin a wheel with a bent axle. The entire drum will move erratically, leading to substantial shaking. You need to address this to prevent further damage.

Repairing or replacing drum bearings is a complex job. It often involves removing the outer tub and using specialized tools. For most homeowners, this is a repair best handled by a professional appliance technician.

Bent Drum Spider

The drum spider is a component that attaches the inner drum to the drive shaft. If it becomes bent, cracked, or corroded, it can cause the inner drum to spin off-center. This leads to a wobbly drum and, consequently, violent shaking.

This is more common in machines with stainless steel tubs that can corrode over time, or if the machine has experienced severe stress. You might see rust or cracks on this component. It’s a critical support structure for the drum.

Replacing the drum spider is a very difficult repair. It often requires disassembling the entire tub assembly. This is typically a job for experienced professionals. You’ll likely need to weigh the cost of repair against a new machine.

Foreign Object Trapped

Sometimes, small objects like coins or bra underwires can get lodged between the inner and outer drums. This can create an uneven surface and cause the inner drum to wobble as it spins. You might hear a scraping or rattling noise along with the shaking.

You may be able to find and remove such objects by carefully inspecting the drum and the area around it. Sometimes, running a cleaning cycle with a few old rags can dislodge smaller items. You want to ensure the drum spins freely.

If you suspect an object is trapped, try using a flashlight to look through the drum perforations. You may need to carefully rotate the drum by hand to find it. Removing it can resolve the wobble instantly.

Loose Inner Drum

The inner drum itself could become loose from its mounting points on the drum spider. This can happen if the bolts or rivets holding it in place fail. A loose inner drum will definitely result in a wobbly spin and significant vibration.

This is a less common issue but can occur, especially in older machines. It indicates a failure of the structural components holding the drum together. You need to ensure the drum is rigidly attached.

Inspecting the connection points between the inner drum and the spider is necessary. If you find loose fasteners or damaged mounting points, this is a significant repair. You will likely need professional help.

Summary Table

Frequently Asked Questions

Is It Normal for a Washing Machine to Shake a Little?

Yes, a small amount of vibration is normal for any washing machine, especially during the spin cycle as it expels water. However, violent shaking that causes the machine to move across the floor, or loud banging noises, is not normal and indicates a problem you should address.

Can a Washing Machine Shake Itself Apart?

While rare, it is possible for a severely unbalanced load or significant mechanical failure, like worn-out suspension components, to cause extreme shaking. If left unchecked, this intense vibration can lead to components breaking off or the machine becoming unstable and damaging itself or your floor.

Are Washing Machine Shock Absorbers Hard to Replace?

Replacing shock absorbers can range from moderately difficult to hard, depending on your specific LG model. It often involves tipping the machine, removing panels, and dealing with spring tension. If you’re not mechanically inclined, it’s often best to call a technician for this repair.

Do I Need to Call a Repairman If My Washing Machine Shakes?

Not always. You should always start by checking simple things like load balance and leveling feet. If those don’t solve the violent shaking, and you’re comfortable with basic tools, you might be able to fix it yourself. However, for complex issues like bearing replacement, a professional is recommended.

How Can I Tell If My Washing Machine is Balanced?

You can tell if your load is balanced by observing the machine during the spin cycle. If it’s shaking violently, making loud banging noises, or moving across the floor, the load is likely unbalanced. Try pausing the cycle and rearranging the clothes so they are evenly distributed.

Will a New Washing Machine Stop Shaking?

A new washing machine should not shake violently. While all machines vibrate during the spin cycle, a new one should operate smoothly and quietly. If your new LG washer is shaking excessively, it could be a manufacturing defect or an installation issue, like improper leveling.

How Much Does It Cost to Fix a Shaking Washing Machine?

The cost varies greatly depending on the problem. Adjusting leveling feet costs nothing. Replacing a drive belt might cost $50-$100 for the part if you do it yourself. Replacing drum bearings or suspension components professionally can range from $200 to $500 or more.

What is the Most Common Cause of a Washing Machine Shaking?

By far, the most common cause of a washing machine shaking violently during the spin cycle is an unbalanced load. Clothes clump together on one side, throwing the drum off balance. Always check your loading habits first.

Final Thoughts

I hope this guide helps you get your LG washing machine running smoothly again. Dealing with a shaking appliance is frustrating, but usually, the fix is straightforward. You can save yourself time and money by understanding the common causes and trying some simple solutions yourself.